UltraSpeed Max Instructions

for Loft, Face Angle, Weights 

NOTE: Your driver comes preset on standard loft (either 10.5 or 12.5) is correctly weighted for the driver length you selected. No further adjustment is needed unless desired. Do not adjust weights until consulting recommended weighting below.

Adjustable Hosel Settings

Hold the club upside down and completely loosen the screw with the provided tool ( use care not to drop the screw and lock washer). Set the desired loft & face angle options by positioning one of the four indicated settings on the line at the back of the hosel: Hand tighten the hosel back in place firmly ( do not try to over tighten ).

Standard Loft (10.5 or 12.5)

with Slight Draw Bias or Neutral Bias with weight in toe port

Standard Loft- Upright Lie

(10.5 or 12.5) with Draw bias or Maximum Draw Bias with weight in heel port

Lower Loft (9 or 11)

with Neutral Bias or slight Fade bias with weight in toe port

High Loft (12 or 14)

with Maximum Draw bias

and added draw with weight in heel port

Weight Instructions

The UltraSpeed ION has 3 weight ports positioned on the Toe, Rear and Heel of the club head (see illustration). Placing weight in these ports can influence ball flight and feel as follows:

Recommended Weights for Driver Lengths

Note: Your driver comes preset for the proper weight and requires no further adjustment

Add the following brass weights to the club head. The remaining weights should be the black plastic 1 gram weights.

IMPORTANT: When removing or installing the black plastic weights do not force or apply undo pressure. Gently turn the screw to extract or install into place. Do not over tighten to avoid stripping. Do not exceed maximum weight recommendations.

Ultra Edition and Easy Edition drivers should use the minimum amount of weight for faster club head speeds

48” – 47.5” length – For faster club head speed just plastic 1 gram weights or, for heavier feel, (1) 5 gram weight. 

47” – 46.5” length – (1) 5 gram. For heavier feel (1) 8 gram . Maximum weight (1) 8 gram & (1) 5 gram

46” – 45.5” length – (1) 8 gram weight. For heavier feel (1) 10 gram.  Maximum weight (1) 10 gram & (1) 5 gram

45”  -  44.5” length – (1) 8 gram weight & (1) 5 gram. For heavier feel (1) 10 gram & (1) 5 gram. Maximum weight (1) 10 gram & (1) 8 gram

44” –  43” length    – (1) 10 gram & (1) 5 gram. For heavier feel (1) 10 gram & (1) 8 gram. Maximum weight (1) 10 gram & (2) 8 gram

42.5" - 42" length    -  (10) gram, (1) 8 gram. For heavier feel (1) 10 gram & (2) 5 gram. Maximum weight (1) 10 gram & (2) 8 gram  

Golfers can set the weighting lighter than recommended if preferred. Do not overweight the club head as excess weight will slow down swing speed and over stress the shaft especially at 47” to 48” lengths.

How to Set For Neutral, Draw or Maximum Draw Bias

Neutral Setting: Place the Adjustable Hosel on Standard Loft and add the desired weight to the Toe Weight Port. Or, place the Adjustable Hosel on the Lower Loft setting and add the desired weight to the Rear Weight Port (if any is required).

Draw Bias Setting: For slight Draw Bias place the Adjustable Hosel on the Standard Loft setting with the desired weight in the Heel Weight Port. For Draw Bias place the Adjustable Hosel on the Upright Setting with the Weight (if any needed) in the Rear Weight Port.

Maximum Draw Bias Setting: Place the Adjustable Hosel on either the Upright Setting or Higher Loft Setting with the weight in the Heel Weight Port.

The weight ports can be used to lessen or increase the effect (for instance: when set for Maximum Draw Bias moving the weight from the Heel to the Rear Weight port can influence a higher ball flight or moving it to the Toe Weight Port can reduce the amount of Draw Bias allowing golfers to tweak the club to better fit the desired ball flight).

Weight Identification

10 gram - longest brass screw

8 gram   - medium length brass screw

5 gram   - shortest brass screw

1 gram   - black plastic screw

Toe Weight Port: (Fade Bias) Placing weight in the toe of the club head promotes a neutral bias or a slight fade bias when used on the Lower Loft setting 

Rear Weight Port: (Neutral Bias & Higher Launch) Placing weight in the rear of the club head promotes neutral bias together with a higher MOI (moment of inertia) which stabilizes the club head at impact while influencing a higher ball flight depending on the amount of weight used. 

Heel Weight Port: (Draw Bias) Placing weight in the heel of the club head promotes additional draw bias and can be used in combination with the adjustable hosel draw bias settings to maximize the effect and influence more draw bias.

Weights can also be split between weight ports (such as heavier weight in Rear and lighter weight in Heel for higher flight with draw bias and so on).